 |
Camsorb® Riga-Sorb
Glide/Pack®
Medium-capacity odor and contaminant control in
a low pressure drop side access housing.The Camsorb® RS
Glide/Pack® can be used for commercial applications,
industrial applications, manufacturing facilities,
medical facilities or any other applications where
the control of gaseous contaminants may be a concern.
It may also be used to reduce ventilation air through
recirculation, thus saving energy during the heating
and cooling seasons.
The Camsorb RS Glide/Pack is an excellent choice
for ventilation air correction in areas of non-attainment
per ASHRAE Standard 62.Each unit provides side-access
housing convenience, for interior or exterior installation,
where the housing mates to other housings or a ducted
HVAC system.
|
 |
Camsorb® Retainer/Pack
Medium-capacity odor and dust control in a low pressure
drop built-up bank system. The Camsorb® RS80
Retainer/Pack can be used in commercial applications,
industrial applications, manufacturing facilities,
medical facilities or any other applications where
the control of gaseous contaminants may be a concern.
It may also be used to reduce ventilation air through
recirculation, thus saving energy during the heating
and cooling seasons.
The Camsorb RS80 Retainer/Pack is an excellent choice
for ventilation air improvement in areas of air quality
non-attainment per ASHRAE Standard 62. Each adsorber
module is a single unit that may be stacked up to
four units high, and any number of units wide, to
form a complete filter bank. Each module may include
48 pounds of adsorbent, a prefilter or dusting filter
and a high efficiency particulate filter.
|
 |
Camsorb® RS
80 Two-Inch Panel
2-inch panel for removal of odors or cleaning of
make-up air at medium loads. Camfil Farr Camsorb® RS
80 two-inch panels can be used to control odors or
limit VOC exposure created by contaminants in the
typical office environment.
They may also be used in areas of non-attainment
to clean make-up air before it is introduced to the
indoor environment.
|
 |
Riga-Sorb
25D
A 2-inch bypass panel for control of low level to
intermittent odors and low-level ozone removal in
non-EPA compliant areas.
Camfil Farr Camsorb RS25D panels can be used to
control low-level or intermittent odors, and/or reduce
ozone levels in geographic areas of EPA non-compliance.
|
 |
3CF
Glide/Pack®
High-capacity gaseous contaminant and odor control
in a side- access filter housing. The Camfil Farr
Camsorb two-stage side-access sorbent panel housing
can be used in commercial applications, industrial
applications, manufacturing facilities, medical facilities
or any other applications where the control of odors
and gaseous contaminants are a concern.
The housing can also be used to reduce make-up air
by increasing recirculated air, thus reducing energy
costs during the heating and cooling seasons. The
Camsorb 3CF Glide/Pack® housing provides side-access
convenience for interior or exterior installation.
It is designed to mate to other housings or installed
in a ducted HVAC system.
|
 |
CF4A
High-capacity gaseous contaminant and odor control
in a modular, built-up bank assembly. The Camfil
Farr built-up bank sorbent panel assembly can be
used in commercial applications, industrial applications,
manufacturing facilities, medical facilities or any
other applications where the control of gaseous contaminants
or odors may be a concern. It may also be used to
reduce outside air by increasing recirculated air,
thus saving energy during the heating and cooling
seasons.
Each Camfil Farr built-up bank adsorber module assembles
into a built-up bank of gaseous and particulate filtration
with 85 pounds of adsorbent per 2000 cfm, a prefilter
(of any depth) and a final filter (of any depth).
|
 |
Camsorb® CF
One-Inch Panels
High-capacity loose-fill plastic panels for gaseous
contaminant & odor removal. The industry standard
for practical odor control, Camfil Farr 1-inch polystyrene
panels (formerly known as Farr CF panels) were the
first high-velocity ‘straight through’ carbon
purification filters available.
Recommended for high gas/vapor load make-up air
and recirculation applications, where high removal
efficiency and a large quantity of sorbent media
is required.
|
 |
Camsorb® Pleated
V-Cell Cartridge
The Camsorb® Pleated V-Cell Cartridge Filter
is designed to fit in place of existing 12" deep
filters within an air-handler. Use of the Camsorb
Pleated V-Cell Particulate + Carbon Cartridge Filter
for dust, pollution and odor control.
The filter also allows make-up air intake flow to
be lowered, thereby significantly reducing operating
costs associated with the energy purchased for heating
and cooling that make-up air. This method for contaminant
removal is specifically prescribed in ASHRAE Standard
62 - Ventilation for Acceptable Indoor Air Quality.
|
 |
Campure™ GDM
440
Camfil Farr’s Campure™ GDM 440 Adsorber
Modules incorporate Campure Molecular Filtration
Media in an easy-to-service disposable plastic module.
Designed to remove corrosive gases from make-up
air streams in commercial/industrial environments.
Exact replacement for existing commercial & industrial
make-up air systems.
|
 |
Campure™ GDM
300
Camfil Farr’s Campure™ GDM 300 Adsorber
Modules incorporate Campure Molecular Filtration
Media in an easy-to-service disposable plastic module.
Designed to remove corrosive gases from exhaust
streams in industrial environments. Exact replacement
for existing industrial exhaust systems.
|
 |
Camsorb® CH
Loose-Fill V-Cell Cartridge
The Camsorb® CH Loose-Fill V-Cell Cartridge
is recommended for reduction of modest occupancy
odor loads, peak-shaving* of ambient air pollutants,
and continuous control of low-level gaseous contaminants
in make-up and air recirculation applications. It
is a cost effective filter for control of odors and
outdoor pollution.
The Camsorb CH Loose-Fill V-Cell Cartridge may be
installed in any HVAC application where the use of
outside air for contaminant dilution is burdensome
and cost-prohibitive to the building operator. Use
of the Camsorb CH Loose-Fill V-Cell cartridge for
contaminant adsorption and removal allows for minimal
introduction and conditioning of outside air, thereby
significantly reducing energy costs associated with
heating and cooling of required make-up air where
a sorbent filter is not applied. This method for
contaminant removal is specifically prescribed in
the ASHRAE Standard 62, Ventilation for Acceptable
Indoor Air Quality.
|
 |
Camsorb® Canister
Holding Frames
Combines high-capacity sorbent canisters with built-up
bank frames for large system gaseous contaminant
control. Camfil Farr built-up bank holding frames
for cylindrical sorbent canisters are recommended
for high gas/vapor load make-up air and recirculation
applications. A sorbent media capacity, of up to
96 pounds per 2000 cfm, provides a higher removal
efficiency than other sorbent systems. This higher
media volume also ensures a higher contaminant loading
capacity than standard HVAC adsorption systems.
Frames are ideal for large system retrofits, custom
air handling systems and other HVAC systems handling
large volumes of air. When properly installed, the
combination of Camsorb holding frames and Camsorb
sorbent canisters ensure that virtually all of the
air flowing through the system will be efficiently
treated by the filters.
|
 |
Camsorb® Canisters
Camfil Farr Camsorb® cylindrical sorbent systems
are recommended for high gas/vapor load make-up air
and recirculation applications, where high removal
efficiency and a large quantity of sorbent media
are required. Applications include:
|
 |
Camsorb® Bag
Filter
Low pressure drop particulate filtration combined
with odor control. The City-Flo bag filter is a totally
new combination dust and odor control filter designed
for urban environments.
Ideal for office buildings, retail stores, shopping
centers, schools and other public buildings, located
in close proximity to heavily trafficked streets
and roads.
|
 |
Campure™ Media
A comprehensive range of molecular filtration medias
for the control of corrosive gases, toxic gases,
odors and other gaseous pollutants. The medias may
be used as part of original equipment packages or
as replacement for spent media. The Campure™ range
comprises chemically impregnated adsorbents based
on activated alumina which may be used on their own
or blended with activated carbon.
|